Plumbing Basics: The First Step for Bathtub Installation
Plumbing Basics: The First Step for Bathtub Installation
Blog Article
The article author is making a few great points relating to How to Install a Bathtub as a whole in this post further down.
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
Setting up a bathtub isn't exactly brain surgery, yet it does need strong plumbing, carpentry, and also sometimes, tiling skills. Changing an old bath tub with a brand-new one is also a reasonably tough job. If the old bathtub is readily obtainable, the project can relocate quickly; if you have to open up a wall surface to get rid of the old bathtub and position the new tub, the job is a lot harder. In either case, the task is within a residence handyman's abilities, although you will certainly require a helper to move out the old tub and set in the brand-new one. See to it you have certified on your own for the job and are comfortable trying it. Rather than working with a service provider to take over a halfway-completed job, it is much better to take into consideration using one prior to you start. Opportunities are you might need a professional plumber to make tube links.
This short article will certainly aid you set up a new tub in your washroom if you have currently acquired a brand-new tub and also do not need to transform the setup of your previous water system pipes.
Your tools and material checklist ought to consist of the following:
Preparing for the Installment
To start with, the supporting framework supplied with the bath needs to be fitted (if needed) according to the maker's guidelines. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is necessary to ensure that if the faucet features a plastic washer, it is fitted between the bath and the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the faucets unit to avoid strain on the bath tub.
Fit the flexible faucet adapters to the bottom of the two taps utilizing 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make certain you use every one of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath must now prepare to be suited its final position.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your setup, then the first thing you ought to do is disconnect the supply of water. After doing so, switch on the taps to drain pipes any water remaining in the system. The procedure of removing the existing taps can be rather problematic due to the limited access that is often the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the taps. Have a towel all set for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been eliminated, make use of the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary taps from turning during this process. When the faucets have been gotten rid of, the holes in the bath/basin will need to be cleansed of any old securing compound.
Before going on to fit the new taps, compare the pipeline connections on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Setting up the Bathtub
Making use of both wood boards under its feet, position the bath tub in the required position. The wooden boards are helpful in evenly spreading the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 tiny points.
The next goal is to ensure that the bath tub is leveled all round. This can be achieved by examining the spirit level and changing the feet on the tub up until the spirit level reads level.
To install faucets, fit all-time low of the outermost flexible faucet port to the suitable supply pipeline by making a compression sign up with; then do the exact same for the other tap.
Switch on the water and examine all joints as well as brand-new pipework for leakages and tighten them if required. Load the bath tub and additionally inspect the overflow electrical outlet as well as the regular outlet for leaks.
Ultimately, deal with the bathroom paneling as defined in the producer's instruction manual. Tiling and sealing around the tub needs to wait up until the bathtub has actually been made use of a minimum of once as this will certainly settle it right into its final placement.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will require a plastic adapter to avoid damages to the string. One end of the port fits on the plastic tail of the faucet as well as the other end gives a link to the existent supply pipelines.
If you require to fit a monobloc, after that you will need lowering couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the mounting hole in the bath/basin ensuring that the washers are in place in between the tap and also the sink. Safeguard the tap in place with the producer offered backnut. As soon as the tap is securely in place, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with typical tap adapters. The previous type needs to be attached to the tap ends first, tightening up just by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bath satisfies the tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the fitting can move enough to split a rigid seal, creating the water to pass through the wall between the bath as well as the tiling, leading to problems with wetness and feasible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your components as well as fittings. They are offered in tubes and also cartridges, and also are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of drenched newspaper or soft rope. Remember to always fill the tub with water before sealing, to allow for the motion experienced when the tub is in usage. The sealant can split fairly very early if you do not take into account this motion before securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise conveniently offered on the marketplace. It is suggested to fit the ceramic tiles making use of waterproof or water resistant adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you enjoy reading up on How to Install a Bathtub? Post a comment below. We would be glad to listen to your suggestions about this write-up. Hoping that you visit us again later on. For those who enjoyed our article plz make sure you remember to share it. I thank you for reading our article about A Step-by-Step Guide to Installing a Bathtub.
One-stop solution, phone now! Report this page